Shorelandr SRV2046T User Manual download pdf (Page 4)

SR-V2046T Final Assembly Instructions

Made in the USA Midwest Industries, Inc. Ida Grove, IA 51445 Tele: 712/364-3365 0002721

Rocker Boxes:

Align the center of the hole of the rocker arm with the

center hole of the spring bracket. Secure with a 3/4 X 4-1/

2 hex bolt from the outside-in and tighten with a 3/4 hex

lock nut.

Axle/Springs:

Fasten the springs to the axle with a 1/2 square u-bolt

over the spring clamp (Ref.#49) and then over the axle.

Secure the legs of the u-bolts to the u-bolt plate (Ref.#50)

and tighten with 1/2 flange lock nuts. NOTE: Make certain

the hook end of the springs point in same direction to the

rear of the trailer, on both axles! For the rear spring and

axle place a galvanized spring bracket bushing in the rear

of the spring bracket. Insert a 9/16 X 32-1/4 hex bolt

through the bracket from the outside-in and tighten with 9/

16 hex lock nuts. Slide the end of the hook spring over

the bushing just installed; raise the front of spring and

fasten with a 9/16 X 3-1/4 hex bolt and a 9/16 hex lock

nut. Repeat on the other side. Tighten all nuts and bolts

but do not over tighten. Allow the spring room enough to

move.

For installation of the front spring and axle repeat the

above procedure, however, place the bushing in the rocker

box in the hook end of the spring. Insert the bolts and

secure with hex lock nuts as before.

Mount the tires and rims using 80-90 ft. lbs. torque on lug

nuts using proper tightening procedures.

Tongue:

Install the tongue assembly into the tongue channel of the

trailer frame. Thread the tongue harness through the

tongue plate cover. Secure the tongue plate cover

(Ref.#56) and the rear of the swing tongue assembly with

a 1/2 X 1-1/2 hex bolt, 1/2 flat washer and 1/2 hex lock

nut. Tighten both bolts. Tighten bolts but do not over

tighten. Match tongue harness wires with the correct

frame harness wires, plug-in. Wiring is complete.

Safety Chain:

Using a ½ X 5 hex bolt on lower right mounting hole on

tongue, secure the safety chain. Place a ½ flat washer on

½ X 5 hex bolt followed by one safety chain and insert

into actuator housing unit and tongue. Place the second

safety chain on the bolt followed by a ½ flat washer and

½ flange lock nut. Tighten.

Brakes:

Refer to the brake manual for service and maintenance.

Winch:

Mount the Profile 2000 winch assembly with jack on the

tongue in a desired location that best fits your watercraft

using three (3) 1/2 X 4 carriage bolts and 1/2 flange lock

nuts. Install the winch handle on the Profile 2000 winch

shaft.

Bunks:

Install and secure the 2X6 bunk onto the bunk brackets

with 3/8 X 1 hex bolts and 3/8 flange lock nuts. Make

sure the bunks are positioned so that the bunk bracket

attached to the bunk and the bracket attached to the

frame are mounted together so that you have metal to

metal stops to keep the bunks from pivoting to far. Tighten

as far as possible but still allow the bunk to fully pivot side

to side.

Assembly should be complete except for tightening

some of the bolts. These bolts were left loose to aid in

adjusting the trailer to the boat only. All bolts and

nuts must be tightened before towing.

NOTE: The law requires that the white ground wire on

both the tongue wire harness and vehicle harness be

properly grounded to respective trailer and vehicle

frames.

Trailer Adjustments

Before adjusting the winch post check to see that the

transom of the boat is flush with rear of the bunks.

Place the boat onto the trailer so that it is resting on the

bunks. The transom must be flush with bunks at the rear

of the trailer. Once the boat is positioned as described

above, make the following adjustments.

Winch Post:

Slide the winch post into position. Note that the winch

holder (upper portion) must be positioned just above the

bow eye. Run the winch strap over the upper nylon

bushing in the winch case and secure to bow eye. Tighten

all bolts on the winch post. Slip the bow eye safety chain

into the bow eye. Adjustment is complete. Check the

tongue weight.

NOTE: Double-check all nuts and bolts to insure that

they are properly tightened before towing.

1 2 3 4

Comments to this Manuals

No comments

Shorelandr SRV2046T User Manual Page 4

Comments to this Manuals

Related products and manuals for Trailers Shorelandr SRV2046T