Shorelandr SLRB46TBBS V.2 User Manual download pdf (Page 4)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003478

Page 4

TONGUE

The tongue is shipped separate of the frame. Locate the appropri-

ate tongue and install by sliding it in the front of the tongue chan-

nel.

Line the holes in the tongue with the holes in the tongue channel.

Install the 1/2” x 4” hex bolt in the front cross hole and secure with

a 1/2” lock nut.

Remove the wire harness from the rear of the tongue. Place the

wire harness and the brake line through the hole provided in the

tongue cover plate. See Detail A in Diagram A.

Secure the tongue cover plate in position with the same1/2” x 1-

1/2” hex bolt that secures the back on thetongue to the tongue

channel of the frame. Secure with 1/2” lock nut. Tighten both bolts

just installed.

Plug the tongue wire harness ends into the frame harnesses by

matching colors and ends. Push the extra wire provided either into

the rear of the tongue or else remove the grommet in the side frame

and place the extra wire in the side frame. Replace grommet just

removed.

WHITE GROUND WIRE INSTALLATION

Place the self-tapping screw provided through the round metal ring

on the white ground wire of the tongue harness located at the rear

of the tongue. Attach the ground wire to the main frame by driving

the screw in the hole provided next to the tongue channel of the

frame. This will assure a positive ground for the lighting.

SAFETY CHAINS

Locate the 1/2” x 1-1/4” hex bolt. Slip the bolt through a 1/2” ﬂat

washer, then place through the last link of one of the safety chains.

Place a second ﬂat washer on the bolt and insert through the hole

as shown in Diagram B. Secure with a 1/2” ﬂange lock nut. Tight-

en.

Repeat this process on the second safety chain on the opposite

side of the tongue. Assembly is complete.

BRAKE LINE

Locate the brass brake line coupling. Remove the plastic cap and

thread the brake line coming out the rear of the tongue into one

end of the coupling. Bend the line in a smooth gradual radius being

careful not to kink the line. Bend so it can be mated to the brake

line from the side frame. Once aligned, thread the side frame brake

line into the other end of the coupling. Tighten both lines into the

coupling.

WINCH POST ASSEMBLY

The height that the bow eye is placed in your boat will determine

the length winch post required. Once this is determined, attach the

winch base to the tongue with three 1/2” x 4-1/2” carriage bolts and

lock nuts.

Align the holes in the Proﬁle 2000 mounting channel with the holes

in the top of the winch base. Attach the front of the winch head

mounting channel to the base by placing a 1/2” x 4-1/2” hex bolt

through the hole closest to the front of the winch base. Secure with

a lock nut. Do not tighten.

Note that the winch head can now be rotated either up or down.

Identify the correct hole combination to use to position the bow eye

roller just above the bow eye of your boat. When determined, se-

cure in this position by placing the bushing as shown in Diagram C

inside the winch base so it aligns with the hole just identiﬁed for the

proper adjustment. Insert another 1/2” x 4-1/2” hex bolt through the

determined mounting hole in the mounting channel and winch base

making sure the bolt passes through the bushing as well. Secure

with a 1/2” lock nut.

Tighten all bolts.

Diagram B

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Shorelandr SLRB46TBBS V.2 User Manual Page 4

Comments to this Manuals

Related products and manuals for Trailers Shorelandr SLRB46TBBS V.2