Shorelandr SLB80TBB User Manual download pdf (Page 4)

Made in the USA Midwest Industries, Inc. Ida Grove, IA 51445 (800)859-3028 0002874

www.shorelandr.com REV B 11/13/00

REF# PART# DESCRIPTION QTY

1 0310224 1/2 X 3-9/16 X 1-1/2 SQUARE U-BOLT ........... 2

2 0810920 1-1/4 PH SCREW ............................................... 8

3 1440102 1/2 FLANGE LOCK NUT .................................... 4

4 3810097 .515 ID X 11/16 OD X 7/16 LONG BUSHING .. 4

5 61767-- BUNK BRACKET ................................................. 1

6 S-3263 GALV. 16 BUNK BRACKET ............................... 2

7 S-3264 GALV. BUNK SUPPORT PIVOT ........................ 2

8 61778-- 36 BUNK ASSEMBLY W/BRACKETS ............... 1

Bunk Material List: 61778--P

REF# PART# DESCRIPTION QTY

1 S-3485 24-1/2 ROLLER ARM ......................................... 1

2 0210127 3/8-24 X 3 CARRIAGE BOLT - 1 THREAD ...... 4

3 1310121 3/4 FLAT WASHER; ALUM. ............................... 8

4 1440100 3/8 HEX LOCK NUT ........................................... 4

5 S-3368 19-1/2 ROLLER PIN ........................................... 4

6 1540350 BULL RING .......................................................... 8

7 S-3184 PLASTIC MOLDED SWIVEL BLOCK .................. 2

8 S-3382 5 ROLLER W/MOLDED HUB ............................. 8

9 S-3383 MOLDED ROLLER BUSHING ............................. 8

10 S-3384 SPECIAL FLAT WASHER ................................... 8

Roller Material List: 60617--

Place the roller assemblies on the rear support tube (Ref.#95).

Secure the roller assemblies in the outside holes of the rear

support tube with 1/2 X 4-1/2 hex bolts and 1/2 flange lock nuts.

Front Roller Cradle:

Install the front roller cradle on the front crossmember and secure

with a 5/8 X 12 hex bolt and 5/8 hex lock nut. Do not over

tighten, the roller cradle should freely tilt aft and the stop built into

the roller cradle frame should contact the front of the

crossmember if it is installed properly. (The front roller cradle is

normally factory installed.)

Assembly should be complete except for tightening some of

the bolts. These bolts were left loose to aid in the adjusting

the trailer to the boat only. All bolts and nuts must be

tightened before towing. NOTE: The law requires that the

white ground wire on both the tongue wire harness and the

vehicle harness be properly grounded to the respective trailer

and vehicle frames.

Trailer Adjustments

Place the boat onto the trailer so that it is resting on either on the

bunks or the roller in the back and on the front keel support pad up

front. Position the boat front to back by having the center of the

rear roller approximately 4 from the transom. The bunk model is

more flexible in its adjustment from to back but the boat should be

positioned so that the transom is being supported by the bunk.

Once the boat is positioned as above make the following

adjustments.

Rear Racks:

Position the racks in the back so that they are located between the

keels or strakes and so that they wont interfere when loading and

unloading. Once positioned, tighten the u-bolts in the mounting

brackets. The up-down adjustment in the rear adjustable mounting

bracket should be in its down position whenever possible to keep

the center of the gravity lower to the ground for better trailering.

The upper position should be used only when fender or frame

clearance is needed.

Bunk:

Position the rear of bunks as previously describe in the rear rack

section. Position the front portion of the bunk in the desired area

and adjust vertically for proper pressure of the bunks to the boat

hull. CAUTION: Do not over adjust the front portion of the bunks

which may lift the keel off the front keel roller cradle.

Winch Post Adjustment:

Once the boat is positioned on the trailer, adjust the winch post to

the boat. Loosen the three (3) 1/2 X 4 hex bolts and move the

winch bracket so that the top rubber bow roller is just above the

bow eye. Tighten.

Slide the winch post assembly against the boat. Tighten the u-

bolts. Adjustment is complete.

NOTE: Double-check all nuts, bolts and fasteners - they must

be tightened before towing.

1 2 3 4

Comments to this Manuals

No comments

Shorelandr SLB80TBB User Manual Page 4

Comments to this Manuals

Related products and manuals for Trailers Shorelandr SLB80TBB