Shorelandr SL60TAL V.2 User Manual download pdf (Page 5)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003354

REV A 2/14/06

Page 5

Diagram E

Tongue:

Fasten the tongue in the rear at the front cross member location with a 1/2”

X 4-1/2” stainless steel hex bolt and 1/2” stainless steel ﬂat washers under

the bolt head and the 1/2” stainless steel lock nut with nylon insert. Move

the tongue up to the lower frame plate of the frame. Line up the holes,

fasten the tongue in the frame with two (2) 1/2” X 3-9/16” X 5” stainless

steel square u-bolts, 1/2” beveled aluminum washers, 1/2” stainless steel

washers and 1/2” stainless steel hex lock nut with nylon inserts at the front

of the tongue plates; . Refer to Detail E and F. Connect the tongue brake-

line to the sideframe with a brakeline coupling (Ref.#30 on page 4).

Safety Chain:

Mount the safety chains to the front on the tongue using a 1/2” X 5-1/2” stain-

less steel hex bolt (Ref#4) with a 1/2” stainless steel ﬂat washer at the head

of the bolt, followed by a safety chain through the drop tongue tube. Place the

other safety chain on the bolt on the opposite side of tongue and secure with a

1/2” stainless steel ﬂat washer and 1/2” stainless steel hex lock nut with nylon

insert. Refer to Diagram E.

Wiring:

Plug in the tongue wire harness to the side frame wire harnesses located on

the ﬁrst crossmember. Pull the wire out the hole in the tongue with either the

brown and yellow or brown and green plug.

White Ground Wire Installation:

The white ground wire must be grounded

to the trailer frame with a 1/4” X 3/4” stain-

less steel self grounding tap screw. At-

tach the ground wire to the main frame by

driving the screw into the bottom ﬂange of

the side frame. This will assure a positive

ground for the lighting.

Brake line:

Place one end of the tongue brake line into

the hole in the top of the tongue located just

behind the front joint of the two side frames.

Insert until the end of the line comes out

the front of the tongue. Place the actuator

into it’s approximate location on the tongue.

Remove the plastic plug in the rear of

the actuator and thread the brake line

into the port. Tighten. Place the ac-

tuator in it’s proper location by align-

ing the holes in the mounting channel

with the holes in the tongue.

Actuator:

M o u n t t h e a c t u a t o r ( I t e m # 1 0 )

t o t h e d r o p t o n g u e s e c t i o n

using three (3) 1/2” X 4-1/2” stainless steel

hex bolts (Item #3) and 1/2” stainless steel

hex lock nuts with nylon inserts.

Place a grommet around the brakeline

where it comes out of the top of the tongue

to keep it from vibrating and chafﬁng as it

is being towed. Form the remaining end

of the brake line so it will mate up with the

brake line running down the side frame.

Secure the two lines together with the brass

coupling provided in Hardware box

66801. Tighten securely to prevent

leaks but do not over tighten causing the

threads in the ﬁtting to strip.

1 2 3 4 5 6 7 8 9 10 ... 19 20

Comments to this Manuals

No comments

Shorelandr SL60TAL V.2 User Manual Page 5

Comments to this Manuals

Related products and manuals for Trailers Shorelandr SL60TAL V.2