Shorelandr LEB29CBLW V.2 User Manual download pdf (Page 9)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com 0003284

REV B 2/07/06

Page 9

SPRINGS

Position the axle so it is properly aligned with the trailer. The end of

the axle that has the brake line hose attached must be to the right

side of the trailer when standing at the rear of the trailer and look-

ing forward. This positioning places the disc brake calipers on the

backside of the axle.

Place the springs on the topside of the spring pads welded to the

axle. (See Diagram D). Note that the hook end of the spring must be

mounted to the rear of the trailer. Place a spring clamp on the top

center of the spring as shown. Next place the 1/2” x 6-1/2” U-bolts

down over the top of the spring clamp, spring and axle as shown.

Place the spring and axle U-bolt plate onto the ends of the two U-

bolts just placed around the axle. Secure with 1/2” lock nuts. Thread

onto the U-bolts but do not tighten securely until the complete unit

is in position on the trailer. Repeat on the other spring.

AXLE

Place one of the spring bracket bushings into the rear of the spring

bracket and secure with a 9/16” x 3-1/4” hex bolt and hex lock nut.

Repeat in other spring bracket.

Position the axle under the frame, then hook the hook loop of the

spring around the bushings just installed. Note that if the axle is

positioned too low when trying to hook, the hooks will not hook

around the bushings.

Raise the front of the springs up so they align with the front hole

of the spring bracket. Secure in place with 9/16” x 3-1/4” hex bolts

and lock nuts.

Tighten all axle U-bolts and spring bolts not tightened at this time.

ONE AXLE BRAKE INSTALLATION

Cut the tape securing the brake line hose to the axle. Remove

the brass plug from the port in the brass block on the right brake

caliper. Thread in the brake hose male end and tighten. Place the

other end of the hose up through the hole provided in the brake line

clip bracket. Secure in place with the hose clip provided.

Remove the plastic cap from the end of the frame brake line coming

out of the side frame by the axle. Carefully uncoil the brake line so

that it will reach the end of the hose just attached to the brake line

clip bracket. Thread the brake line ﬁtting into the brake line hose.

Tighten. All bleeding to the line can be done through the bleeder

on the right caliper.

Fill the actuator reservoir with brake ﬂuid and bleed the line per the

instructions in the brake manual. Note that the axle is already bled

at the factory during assembly. All bleeding to the line can be done

through the bleeder on the right caliper.

TIRE & WHEEL ASSEMBLIES

Mount the tire and wheel assemblies using the 1/2” ﬁne threaded

tapered lug nuts provided. Tighten to 80-90 ft/lb. of torque using the

rotation pattern as shown in the ShoreLandr’s Owners Manual.

Re-torque the lug nuts after 50 miles of driving and then periodi-

cally thereafter.

Tire Size and Carrying Capacity Chart

Tire Size ............................ST215/75R 14-C

GVWR ...............................3740 lb.

Carrying Capacity ............2900 lb.

Axle ...................................Brake

Refer to the tire side wall for correct tire pressure.

1 2 3 4 5 6 7 8 9 10

REV B 2/07/06 1
Diagram A 2

Comments to this Manuals

No comments

Shorelandr LEB29CBLW V.2 User Manual Page 9

Comments to this Manuals

Related products and manuals for Trailers Shorelandr LEB29CBLW V.2